Hello, gentle readers, whoever you are.
For two days this week, we had no rain. That’s both good and bad, as we were working on a couple of projects: my brother on the chickshaw that will hold the layer birds, and me on the chicken tractor for the meat birds. His was a much more complicated build than mine (and the finished product looks awesome, thanks, bro!).
I had an issue with a couple of the joints on the tractor, and I thought I was going to have to break those joints and redo them. Now, naturally when you create a PVC joint with cement, you want them to be there forever (or as close as forever you can get). And, if you do a search on how to break a cemented PVC joint, there are tons of people telling you it cannot be done – they say resign yourself to your fate and hacksaw the joint out and redo it completely because cement is forever.
These people have never heard of chemistry, I expect. Of course joints can be broken, just like (say) cemented bricks can be broken. For the latter, it’s just a matter of brute force with a hammer and chisel or (in larger settings) a jackhammer. For PVC, brute force is unlikely to work – but really, you just need to heat the joint in order to break the bond the chemical reaction creates when cement is applied to the PVC. If you have lots of toys, you can superheat a piece of metal that fits inside the joint, leave that in place for a minute or two, and then remove the metal and pull apart the joint. Or, you could just use a heatgun and aim it at the joint. As it happened, I did not have to redo any joints.
And then, it rained. A ton: just over an inch and a half in about half an hour. At the peak of the downpour, it was falling at a rate of over four inches an hour.
I had put a temporary tarp on the tractor, just to see how it would look It lost its tiedowns.
Einstein kept watch over things.
This morning, I went out to take a look at it, and found that Mother Nature yesterday called out all those people who claimed joints couldn’t be broken.
The design obviously needs a bit more support on the crossbars. The original design uses metal roofing panels on the back end, which lends a tad more structural support, but I can’t use that here, as then we’d have our own personal solar powered chicken roaster. But as to the joints: I found these two broken joints..
These are where the door to the front of the pen lies and the second crossbar, respectively.
Do you know how hard it is to get a section of PVC back in when the two ends are not easy to completely get to and when the entire section would need to be disassembled? I managed to get it back in place with (new) cement, then added a brace at the joint where the door sits on the first crossbar.
I hung up the waterer at the front of the pen, and the food at the rear, for two reasons: one, so the feed wouldn’t get wet – the feeder has an open top. Two, it’s to force them to get some exercise, versus just plopping down and spending the rest of their days parked in front of the food and water, were they together.
Then, it was time to separate the meats birds from the layers and toss them out into their new home. Mother Nature decided to join the party.
I had to hustle to beat the gigantic storm that was showing up on the radar, so I went to the brooder and captured the meaties, putting them into a bin for transport. For all their squawking when I was catching them, they calmed right down and settled nicely.
I put the birds, bin and all, into the tractor, then slowly tipped the bin to its side to give them access to the open ground. They were hesitant to leave the bin initially, but finally made their way out.
The storm was advancing, so I left the birds to figure things out (and hopefully, one of those things to figure out was to get out of the rain, since they are generally not terribly bright).
I went out after the first round of rain and only found a small pool of water on the tarp, so that’s promising. I also found them all piled into the bin, which I’d left in place on its side, and which I will leave there throughout their growth. I had to crawl into the back end of the tractor and toss some food into a trail to lead to the feeder. They hadn’t quite made it before the storm forced me back inside.
This is their first night out in the tractor on the grass. I’m restraining myself from popping out there with the flashlight to see how they are. Either the tractor is secure and they will be fine, or it is not, and something will get them (and I will learn a lesson from that). I’m hoping they’ll find the waterer. I’ve had the same type of waterer in the brooder (sitting on a brick versus hanging) since the end of their first week, and if they can’t keep that in their tiny brains, I’ll have to crawl in once more.
Coming up: looking over the chickshaw.
Until next time, peeps: be well.